There are several reasons for removing and installing a new toilet in the washroom. The one-piece toilet is a special kind that must be in the main stigmatic position to be ripped off for many reasons. You need to have changed the entire bathroom scenario or have an aesthetic purpose. Whatever may be the cause, you need to be very concerned about the removal process of the one-piece toilet.
The present toilet may be leaking, so you need to have a renewal or maybe remove the washroom items. The list goes on. This article is about how to draw a one-piece toilet easily. The replacement process may be hard if you do not know the actual process. So here we have taken the opportunity to hand over the actual situation of traditionally removing the one-piece toilet system. So let’s have a keen look into the process.
Tools you need:
- Adjustable wrench
- Caulk gun, Box spanner
- Hacksaw or pipe cutter
- Cordless drilling machine
- Spirit level and Locking pliers
- Sponges and Bucket
- Wet vacuum with Slip-joint pliers
- Tape measure, putty sharp knife
- 4-in-1 Screwdriver and plier
- Hammer and Toilet shims
- Wax ring and Teflon tape
- Bolts for the toilet seat
A full process of removing a one-piece toilet
Here, a conclusive guideline on removing a one-piece toilet,
Step 1
The very initial phase is to collect all the tools that you need. Place the cloth on the floor that may help catch any drips. Disconnect the water supply line before starting the process. Turn off the water supply but make sure the main water shutoff valve is off.
Step 2
Then, flush the toilet, place rubber gloves, and use a sponge to suck all the remaining water. Take the tank lid off and then soak all the remaining water. The next thing you do is remove the toilet cistern.
The toilet cistern is the tank that is applied in the flushing system. Then separate the rest of the parts from having to address them in a good manner. The cistern is physically one of the most crucial parts of the toilet. The cistern is attached to the toilet, so you need to remove that.
Remove the cistern lid as it is lifted in a while. The cistern may be in a restrictive manner as to call the flush down button. The lever must be in a position that is known to the system of the toilet. Then apply a screwdriver to unscrew the bolts. The bottom part of the cistern has a close liaison with the flushing mechanism. Remove the bottom bolts and then apply that with a new set of screws. You can also use a plier or a wrench to rotate the screws.
Step 3
In the case of the one-piece toilet, you need to have a non-separate tank from the bowl convention. You can apply a wrench to loosen the mounting bolts. The bottom of the tank needs separate mounting bolts because it is a special form of mechanics. A one-piece toilet has been moved right down for more floor bolts inauguration.
The plastic caps need to be decently merged, and the system needs two-floor bolts for securing the toilet to the floor. You need to have a separate putty knife for tormenting the concession of the screws. Apply a screwdriver to loosen the nuts. The washers and bolts need to be implemented so that the entire arena becomes inseparable.
Step 4
The next step is to detach the toilet. You need to be very much sure about the line of caulk implementation. The toilet’s base must be cooperated with the utility knife to detach the caulk. If it is a part of a remodeling project, then you need to be very much sure about the remaining working mechanism. Then rock the toilet as soon as you can. The bottom of the toilet is stuck with the floor in a very wild manner. So the thing is that you must be very prudent about the inclusion of the transfer system.
Lift the toilet bowl gently and slowly, so it doesn’t have any cracks.
Step 5
Finally, apply a knife to remove the worn-out wax ring. The pipe has to be on the side of the connection that has some of the best drainage areas to fit over. If the base is still leaking, you need a new toilet. Before implementing a new one, the thing is that you need to be so much more Cathy to discard the old one. A broken flange can cause leaking foul smiles and sewage odor. So scrutinize the flange. Installing a new one-piece toilet is so much more difficult than maintaining all the possible precautions. You always need a professional plumber to solve all the issues. In the very last stage, make the replacement like it has nothing to do with the nuisance.
Final Words
Replacing an old one-piece toilet is so tiresome if you do not have the real idea of terminating the old one. It seems daunting, but for the customer’s convenience, we have discussed the whole process in a nutshell. As long as the time has the right equipment, it really mixes up with the insurgency. You need to follow the steps depicted in this article. If you feel you cannot do the task, then call in a plumber. The important thing to keep in memory is that the water supply is turned off before initiating the process. We hope this feels easy to remove the one-piece toilet after having this article.
We are really lucky to have a hard-working, multi-skilled plumber on our team. Collin D. Gallegos, a professional plumber who has worked with us since 2012, is an expert in vent, septic, and drainage systems. He is a Certified Master Plumber and has worked on various commercial plumbing projects. He usually helps our readers resolve plumbing and pipe-related issues with a proper DIY troubleshooting and repair guide.